Skiaform

Skiaform / Guides / Calculator

Free design tool

Geodesic dome calculator

Use this geodesic dome calculator to turn your chosen diameter and frequency into strut lengths, hub angles, panel counts and a stock cut list. You can compare sizes, rotate the model and export your results as CSV. Start with the default 16 ft 3V shape, then adjust the settings to explore your own geometry.

Dome
Size is the

Uneven base ring
Units shown
Connection system

Stock and cutting

Model

Drag to rotate. With the view focused, arrow keys rotate, + and - zoom, 0 resets.

    Struts

    Cut list

    First-fit decreasing: longest pieces first, each into the first stick with room. Every piece is charged one kerf.

    Hubs

    Struts are listed in order around each hub; | marks the open side at the base. Plan angles are between neighbouring struts, measured in the plane square to the hub axis.

    Panels

    Flat triangles between hub centres. Mirror pairs matter for sheets with a UV side or flutes.

    Base ring

    Geometry only. Lengths are for flat-face Class I subdivision (method 1), the same convention as the common published chord factor tables. This page does not check strength, wind, snow or anchorage; a structure people use needs a design checked against local codes.

    What the calculator gives you

    You get lengths and quantities for each strut type, grouped hub angles, triangular panel types and a rotatable model. Choose feet, inches, metres or millimetres for your input and display units. The totals help you compare height, floor area, surface area and enclosed volume as you change the shape.

    Your cut list packs pieces into a chosen stock length, allowing for saw kerf and end trim. It places the longest pieces first, then tries each piece in the first stick with room. Treat this as a repeatable cutting arrangement rather than a guarantee of the fewest possible sticks. Download CSV for the tables, or export vertices and struts for your own drawing workflow.

    How to read the results

    A chord factor is a strut length divided by the sphere radius. Multiply it by your radius to recover the distance between hub centres. The letters A, B, C and onward sort equal-length struts from shortest to longest. Other tables can assign letters differently, so compare the numerical factors when checking your results.

    The end angle is half the central angle subtended by a strut. You use it as the bend at a flattened conduit end, or the tilt from square for a timber end face parallel to the hub axis. The strut-to-radius angle is its complement. Hub plan angles measure consecutive struts projected onto the tangent plane; true angles measure them in three dimensions.

    Panel types group triangles with the same three strut letters. Mirror counts matter when your sheet has a UV side or directional flutes. The underlying chord factors and counts were checked against Desert Domes, Domerama and SimplyDifferently. You should compare the same Class I, method 1 geometry and truncation.

    Choosing a frequency and size

    For an icosahedral half dome, 2V uses 65 struts in two lengths; 4V uses 250 struts in six lengths. You get more, shorter members and smaller triangles at the higher frequency, with more pieces to label and assemble. Increasing diameter at a fixed frequency scales lengths while keeping the strut counts unchanged.

    The standard 3V 5/8 option uses 165 struts in three lengths and reaches about 0.5938 times the diameter in height. Its natural base varies vertically by 0.798% of the diameter, about 1.53 in at 16 ft. You must accommodate that variation. Flattening the base changes affected lengths and increases this option to seven strut types; the 2V and 4V half domes already have planar bases.

    Hubs and connectors

    Use the reported hub sequence and plan angles to understand where struts meet around a joint. For plywood geodesic dome hubs, those angles inform a gusset layout, while the end angles describe how members approach it. You still need to resolve plate thickness, fasteners, edge distances and member seating in your connection design.

    For geodesic dome connectors made from pipe or conduit with flattened ends, check the hole-to-end allowance and the bend at each end. Commercial socket connectors can need a different centre-to-strut allowance. Select the corresponding connection system and enter dimensions from your actual detail before using the cut list for a diy geodesic dome.

    Geometry and safety

    You receive geometry, not structural capacity. The calculator does not establish member strength, joint resistance or stability. Snow and wind loads, anchoring, and any occupied or permitted structure need a licensed engineer and a local code check. Have those requirements resolved for your site, materials and connection details before construction.

    Frequently asked questions

    Does the size mean radius or diameter?

    You can select either meaning beside the size input. Chord factors always multiply the sphere radius, so a 16 ft diameter means an 8 ft radius.

    Are the listed lengths ready to cut?

    You need to choose a connection system and enter its allowances first. Hub-centre lengths describe the geometry; your connector dimensions determine how those become physical cut lengths.

    Why does a 3V base need shims?

    You keep the exact published strut sets when you retain the natural base. The base-ring table shows each raised hub's offset above the lowest one, so you can identify the variation before detailing the support.

    Can you save and share a configuration?

    Your settings appear in the URL hash as you edit them. Use Copy link or save the address to return to the same configuration, and keep a CSV alongside it for your records.

    Does this explain how to build a geodesic dome?

    You can use the geometry to understand the parts and their relationships. You still need construction details, a suitable assembly method and the engineering and code checks described above before you build.